71M6533/G/H and 71M6534/H Data Sheet
FDS_6533_6534_004
To facilitate transition to SLEEP mode, which is useful when an unprogrammed IC is mounted on a PCB
with a battery installed, the Teridian production test programs the following six-byte sequence into the
flash location starting at address 0x00000: 0x74 - 0x40 - 0x90 - 0x20 - 0xA9 - 0xF0. This sequence
decodes to the following assembler code:
0000: 7440
0002: 9020A9
0005: F0
MOV A,#40
MOV DPTR,#20A9
MOVX @DPTR,A
; set bit 6 in accumulator
; point to I/O RAM address 0x20A9
; set bit 6 (sleep) in 0x20A9
Transitions from both LCD and SLEEP mode are initiated by wake-up timer timeout conditions or
pushbutton events. When the PB pin is pulled high (pushbutton is pressed), the IE_PB interrupt flag (SFR
0xE8[4]) is set, and when the wake-up timer times out, the IE_WAKE interrupt flag (SFR 0xE8[5]) is set.
In the absence of system power, if the voltage margin for the LDO regulator providing 2.5 V to the internal
circuitry becomes too low to be safe, the part automatically enters SLEEP mode (BAT_OK false). The
battery voltage must stay above 3 V to ensure that BAT_OK remains true. Under this condition, the
71M6533 and 71M6534 stays in SLEEP mode, even if the voltage margin for the LDO improves (BAT_OK
true). Table 50 shows the circuit functions available in each operating mode.
Table 50: Available Circuit Functions
Circuit Function
System Power
MISSION
Battery Power (Nonvolatile Supply)
BROWNOUT LCD SLEEP
CE
CE/MPU Data RAM
FIR
Analog circuits:
MPU clock rate
MPU_DIV
ICE
DIO Pins
Watchdog Timer
LCD
EEPROM Interface (2-wire)
EEPROM Interface (3-wire)
UART
Optical TX modulation
Flash Read
Flash Page Erase
Flash Write
XRAM Read and Write
Wakeup Timer
Oscillator and RTC
XRAM data preservation
V3P3D voltage output pin
GPO – GP7 registers
Yes
Yes
Yes
Yes
From PLL, as
defined by
MPU_DIV[2:0]
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
28.672 kHz
(7/8 of 32768 Hz)
Yes
Yes
Yes
Yes
Yes (8 kb/s)
Yes (16 kb/s)
300 bd
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
– indicates not active
58
Rev 2
相关PDF资料
71M6543F-IGT/F IC ENERGY METERING
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
相关代理商/技术参数
71M6533H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6533H-IEL 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IEL/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel